Wilkins 1" 375 Reduced Pressure (RP) assembly for non potable use.  This does not meet lead free requirements.

Blow out fitting for the 350 and 350XL models.  This will allow you to blow out your sprinkler lines without damaging the assembly.  

It replaces the vessel and this can be left in for the winter.

WILKINS #1 CHECK RETAINER FOR THE 4" 350/450 OR 375/475.  IT IS ALSO THE RETAINER FOR THE #1 CHECK FOR THE 2 1/2", 3" AND 4" 350A AND 375A

WILKINS  POPPET ASSEMBLY FOR  MODELS 950XL, 950XLT, 950XLT2, 975XL AND 975XL2  SIZES 1 1/4", 1 1/2" AND 2"

IF YOU NEED MORE THAN ONE CALL ME AT 801-355-6736 AND WE CAN TALK ABOUT HOW YOU CAN BUY TWO IN A KIT FOR LESS AND GET MORE COMPONENTS.

THESE ARE FOR THE WILKINS 950XL, 905XLT, 950XLT2 AND 975XL AND 975XL2 1/2" - 2" ASSEMBLIES.

UNDERSTAND THAT THESE ARE NOT DESIGNED TO HOLD THE SEAT ON THE TOOL AS YOU TRY AND INSTALL IT BACK INTO THE ASSEMBLY.  THE PURPOSE OF THESE TOOLS IS TO LOOSEN AND TIGHTEN THE SEATS.

THEY DO BETTER THAN THE TOOLS FROM THE MANUFACTURER. THEIRS IS A FLAT PIECE OF METAL THAT CONTACTS TWO OF TEH FOUR STUBS THAT POINT INTO THE CENTER OF THE SEAT.  THESE MAKE CONTACT ON ALL FOUR, USES A RATCHET TO PUT THEM IN AND OUT AND WILL ASSIST IN GETTING THE SEAT STARTED FLAT SO NOT AS LIKELY TO CROSS THREAD THEM.

1" 350 AND 350XL RUBBERS FOR BOTH CHECKS. AND HOUSING O-RINGS

This is the complete plastic vessel with the internals in it for the Wilkins 350 OR 350XL 1"

FOR 1" MODELS 375 AND 375XL RUBBER KIT.  THIS IS THE RUBBER FOR BOTH CHECKS AND RELIEF VALVE.

375 AND 375XL 1" WEDGE KIT

THIS KIT IS FOR THE 420 AND 420XL MODELS.  SIZE 1".  INCLUDES: FLOAT ASSEMBLY, CHECK ASSEMBLY, BONNET AND BONNET O-RING. 

420 1" RUBBER KIT

Complete internals for a 460 or 460XL in 3/4" or 1" size.

Rubber replacement kit for the 3/4" and 1" 460 or 460XL spill resistant vacuum breakers (SVB).

1/2", 3/4" and 1" 720A repair kit.  All internal parts below the brass bonnet that threads into the body.

950 10" CHECK RUBBER KIT

350/375 AND THE 350XL AND 375XL1 1/4", 1 1/2" and 2" BLOW OUT FITTING TO BE USED TO WINTERIZE IRRIGATION LINES.

REPLACES THE VESSEL PORTION OF THE 350/350XL OR 375/375XL.

WILKINS 350 AND 350XL 1 1/4"-2" RUBBER KIT

375 AND 375XL 1 1/4"-2" COMPLETE RUBBER KIT FOR BOTH CHECKS AND THE RELIEF VALVE.

950 COMPLETE KIT 1 1/4"-2"

2" WILKINS RUBBER KIT

FOR MODELS 950XL, 950XLT AND 950XLT2. COMPLETE KIT FOR SIZES 1 1/4"-2".  THIS IS JUST THE CHECK RUBBERS AND SPRINGS FOR BOTH CHECKS.

1 1/4"-2" 950XL/975XL/975XL2 REPLACEMENT CHECK SEAT KIT OF BOTH SEATS AND SEAT O-RINGS